You
can have it all!
The PMX-III
measures kVp, time, and dose - even more accurately than most others. You can
also measure non-invasive mA, light output, and visualize a variety of
waveforms. You have it all - in one meter!
Suited
for Radiology
|
You can use the PMX-III for radiographic or
fluoroscopic exposures. Your results will be accurate at both low and high
mA. At short or long distances. All without orientation dependence. And you
never need to reset - just change generator settings and take your next
exposure.
|
|
PMX-III is a very compact system
|
Since the PMX-III is waveform independent, you can always be sure of accurate
results no matter what type of generator you check.
Short exposure time is no problem for the PMX-III. With a special lock mode
it is possible to measure kVp at exposure times as short as 3 ms.
With the built-in electrometer, measurements of dose, dose rate, mA, mAs,
light from CRTs, and much more are possible. With the solid state detector
R25 and the preamplifier AMP-1 connected, PMX-III measures dose rate to image
intensifiers from 0.03 µGy/s (3µR/s).
Two
Configurations
With the
PMX-III R/M, there are six different mammographic kVp calibrations included
as standard. These six calibrations cover the whole range of target/filter
combinations frame Mo/Mo and Mo/Al, to Rh/Rh and W/Rh.
|
The PMX-III R/CT is specially designed for CT readings. You will
benefit from two unique advantages:
1. There are always two standard calibrations included, and the possibility
for two extra user specified calibrations.
2. The PMX-III R/CT does not force you to take the CT unit out of service.
By using the waveform analyzer can measurements can be acquired while the
tube is rotating.
|
|
PMX-III remote controlled.
|
PMX-III PRO Kit
The PMX-III Pro Kit is a complete and powerful package for X-ray QA.
It is configured around the PMX-III. The PMX-III Pro Kit provides a full compliment
of test equipment for any X-ray room. The powerful QA software oRTIgo for
Windows is included for easy collection and storage of data.
Click on the picture for close-up.
|
Configured around the popular PMX-III
Multimeter, the PMX-III PRO kit provides the service professional with a
full compliment of test equipment for any X-ray room. kVp, time, dose and
dose rate are measured with only one exposure, and this is just the
beginning.
Output from an I.I. is not a problem because of the AMP-1
pre-amplifier. Radiographic, MAMMO and I.I. outputs are easily captured
with the addition of the new ADI Multi. A simple turn of the ADI dial
allows the R25 solid state dose detector to be used with multiple
radiographic and mammographic configurations.
|
- PMX-III R/M or R/CT
- Waveform Analyzer
- oRTIgo for Windows
- Dose Detector, R25
- ADI Multi
- AMP-1, Pre-amplifier
- L-100 Light Detector
- HVL Stand and Filters
- Detector Extension Cable
- Hard Sided Carrying Case
- Manuals
- Measuring Tape
- Swiss Army Knife
|
O = Optional, S = Standard
|
MAS-1, MAS-2, and MAS-3
|
mAs meters
|
O
|
|
ADP-3
|
bias power supply
|
O
|
|
AMP-1
|
preamplifier
|
O
|
|
R25 and R100
|
solid state dose detectors
|
O
|
|
L100
|
light detector
|
O
|
|
Magna 3 cc
|
ionization chamber
|
O
|
|
HVL stand and filter kits
|
|
O
|
|
Detector extender DEX-80
|
positioning of dose detector
|
O
|
|
EXT-1
|
extension cable
|
O
|
|
CAS-3 and Padded case
|
carrying cases
|
O
|
|
WDCT 10, WDCT 16, and PP-8/12T
|
CT ionization chambers / phantoms
|
O
|
|
WAV-2
|
waveform analyzer
|
O
|
|
oRTIgo Software
|
|
O
|
|
|
